GW-LS11 Landslide Deep Displacement Pressure Flow Observation System

This system is mainly used to observe the water content, pore pressure and displacement of the accumulation landslide during the process of precipitation and snowmelt. By arranging meteorological stat

  • Product Name:GW-LS11 Landslide Deep Displacement Pressure Flow Observation System
  • Model:GW-LS11
  • Country:USA

This system is mainly used to observe the water content, pore pressure and displacement of the accumulation landslide during the process of precipitation and snowmelt. By arranging meteorological stations at the location of the moraine landslide, the temperature, precipitation and snow cover in the area are observed; displacement, pore pressure and water content sensors are arranged in the deep part to observe the pore pressure and pore pressure in the deep part of the slope in real time during the process of rainfall or ice and snow melting. Changes in water content and generation of slope displacement. Through this series of means, various factors in the sliding process of the landslide in the moraine accumulation layer are fully collected to provide basic data for the study of its initiation mechanism.


Features:

•Suitable for scientific research and standard measurement;

•Easy to install and maintain;

•High measurement accuracy, without manual participation;

• Flexible configuration of elements;

• It integrates data acquisition and wireless communication, and has chart display function;

• The data collection density can be set by yourself;

• Status monitoring;

• Support AC/solar power supply;

•Maintenance-free, suitable for field applications;

• It can be used for single station application or wireless data transmission;

• Mass data storage.


Measurement and Control Datalogger CR1000X

 

AM16/32B16- or 32-Channel Relay Multiplexer

-NOTE-  The protection on the reset, clock, and +12 V inputs are provided by 18 V TVS diodes.

Power:   Unregulated 9.6 to 16 Vdc

Scan Advance:      Occurs on the leading edge of the clock pulse transition (from below 1.5 V to above 3.3 V)

Minimum Clock Pulse Width:     1 ms

Maximum Actuation Time for Relay:   20 ms

Relay Operation:   Break before make

Initial Relay Resistance, Closed:   0.1 ohm

Maximum Switching Current:  500 mA(Switching currents greater than 30 mA [occasional 50 mA current is acceptable] will degrade the contact surfaces of the mechanical relays and increase their resistance.This will adversely affect the suitability of these relays to multiplex low voltage signals.Although a relay used in this manner no longer qualifies for low voltage measurement, it continues to be useful for switching currents in excess of 30 mA.)

Maximum Switching Voltage:   50 Vdc   A voltage divider such as the VDIV10:1 may be needed between the AM16/32B and the data logger to stay within the input limits of the data logger channel.

Minimum Contact Life :   5 x 107 operations

Maximum Contact Voltage Rating:         70 V

Maximum Voltage:      8 Vdc (clock level)

CE Compliance:    EN 61326:1998

EN 55022:1998 Class B

Surge:    Complies with IEC61000-4-5, test level 3 (±2 kV, 2 ohm coupling impedance)

Operating Temperature Range   :  -25° to +50°C (standard)

-55° to +85°C (extended)

Dimensions:        23.9 x 10.2 x 4.6 cm (9.4 x 4.0 x 1.8 in.)

Weight: ~680 g (~1.5 lb)

ESD

Air Discharge :   Complies with IEC61000-4-2, test level 4 (±15 kV).

Contact Discharge:     Complies with IEC61000-4-2, test level 4 (±8 kV).

Typical Current Drain

Quiescent: < 210 µA

Active:   6 mA (typical in 2x32 mode)

11 mA (typical in 4x16 mode)

Reset Levels:    Inactive    < 0.9 V

Active      3.3 to 8 V


HygroVUE10 Digital Temperature and Relative Humidity Sensor with M12 Connector

Sensing Element       SHT35 modified by Campbell Scientific

Communication Standard    SDI-12 V1.4 (responds to a subset of commands)

Supply Voltage  7 to 28 Vdc

EMC Compliance Tested and conforms to IEC61326:2013.

Standard Operating Temperature Range     -40° to +70°C

Main Housing Material   UV stable, white PET-P

Electronics Sealing Classification    IP67

Sensor Protection    Outer glass-filled polypropylene cap fitted with a stainless-steel mesh dust filter with nominal pore size of < 30 µm. The sensor element has a PTFE protective film with a filtration efficiency of > 99.99% for particles of 200 nm or larger size.

Sensor Connector  M12, male, 4-pole, A-coded

Cable  Polyurethane sheathed, screened cable, nominal diameter 4.8 mm (0.19 in.)

Field-Replaceable Chip or Recalibrate   Field-replaceable chip

Sensor Cap Diameter      12.5 mm (0.5 in.)

Body Diameter at Connector  18 mm (0.7 in.)

Length       180 mm (7.1 in.) without cable fitted

Sensor Body Weight 50 g (1.8 oz)

Weight       250 g (8.8 oz) with 5 m (16.4 ft) cable

Relative Humidity

Measurement Range       0 to 100% RH

Accuracy       -NOTE- The accuracy figures quoted are the 95% confidence limits relative to factory standards.

±1.5% (at 25°C, over the range 0 to 80% RH)

±2% (at 25°C, over the range 80 to 100% RH)

Short-Term Hysteresis     < ±1% RH

Additional Errors at Other Temperatures     < ±1% RH (over -40° to +60°C)

Long-Term Stability        ±0.5% per year (maximum drift in clean air conditions)

Reported Resolution 0.001% RH

Repeatability     0.05% RH (3σ noise level)

Response Time with Filter       8 s (63% response time in air moving at 1 m/s)

Air Temperature

Measurement Range       -40°C to +70°C

-NOTE- The accuracy figures quoted are the 95% confidence limits relative to factory standards.

Accuracy       ±0.2°C (over the range -40 to +70°C)

±0.1°C (over the range 20 to 60°C)

Long-Term Drift       < 0.03°C per year

Reported Resolution0.001°C

Repeatability     0.04°C (3σ noise level)

Response Time with Filter       < 130 s (63% response time in air moving at 1 m/s)

Calibration Traceability NIST and NPL standards

Maximum Current Drain

Quiescent  50 µA

During Measurement      0.6 mA (takes 0.5 s)

200-03002 Wind speed and direction sensor

TE525MM tipping bucket rain gauge

SR50A Snow Thickness Sensor

PTS-420 Displacement Sensor

Relative Humidity Sensor

(For more technical parameters, please leave a message)