:: Product Information

Tripod and Tower Mounts

Campbell

CM202 2-foot Crossarm with Bracket

The CM202 is a crossarm that attaches to an instrumentation tower or tripod. It provides a rugged, weather-resistant sensor mount for one sensor. The CM202 is compatible with all of our tripods, towers, and CM200-series brackets. It can also be attached to a user-supplied pole.
The 1-inch diameter aluminum crossarm is 2 feet (0.6 m) in length and includes a CM210 bracket kit. The stainless-steel CM210 allows the CM202 to attach to either a 3/4- or 1.0-inch-diameter vertical pipe.

Features

Compatible with our CM6 Tripod, CM10 Tripod, CM110 Tripod, CM115 Tripod, CM120 Tripod, UT10 Tower, UT20 Tower, or UT30 Tower
Secures to tripod or tower with u-bolts
Uses CM210 Bracket Kit to attach to a 3/4-inch or 1.0-inch pipe

Specifications

Mounting Bracket Material: 304 stainless steel bracket, with stainless-steel U-bolts and hardware
Crossarm Material: 1” IPS anodized aluminum pipe


CM204 4-foot Crossarm with Bracket

The CM204 provides a rugged, weather-resistant sensor mount for one or two sensors. The CM204 is compatible with our CM6/10-series tripods, CM110-series tripods, or UT-series towers. It can also be attached to a tripod mast or a user-supplied pole. The 1" diameter aluminum crossarm is 4 feet in length and is fitted with CM210 bracket kit that allows it to attach to either a 3/4" or 1.0" diameter vertical pipe.

Features

4-foot crossarm for sensor attachment
Attaches to tripod mast or pole
Includes one CM210

Specifications

Mounting Bracket Material: 304 stainless steel bracket, with stainless-steel U-bolts and hardware
Crossarm Material: 1” IPS anodized aluminum pipe


CM206 6-foot Crossarm with Bracket

The CM206 provides a rugged, weather-resistant sensor mount for up to two sensors. The CM206 is compatible with our CM6/10-series tripods, CM110-series tripods, or UT-series towers. It can be attached to a tripod mast or a user-supplied pole.
The 1" diameter aluminum crossarm is 6 feet (2.0 m) in length and is fitted with CM210 bracket kit that allows it to attach to either a 3/4" or 1.0" diameter vertical pipe. If the CM206 will be mounted on a UT-series tower, an additional CM210 bracket can be added so that the crossarm is secured to two of the three vertical risers within the tower.

Features

6-foot crossarm for sensor attachment
Attaches to tripod mast or pole
Includes one CM210

Specifications

Mounting Bracket Material: 304 stainless steel bracket, with stainless-steel U-bolts and hardware
Crossarm Material: 1” IPS anodized aluminum pipe


CM210 Crossarm-to-Pole Bracket
 
The CM210 is a mounting bracket that is used to attach a crossarm to a instrumentation tripod or tower. One CM210 is included with a CM202, CM204, or CM206 crossarm.
When attaching a crossarm to a UT-series tower, a second COM210 can be purchased to attach the crossarm to a second leg on the tower. The CM210 is "creased" during the manufacturing process, allowing pipes of varying diameter to seat snugly into the bracket when attaching it to the mast or legs of one of our tripods or towers.

Features

Attaches a crossarm to an instrumentation tripod or tower
Accommodates crossarms of varying sizes
One included with each CM202, CM204, or CM206 crossarm

Specifications

Material: 304 stainless steel bracket, with stainless-steel U-bolts and hardware
Includes four u-bolts:
two 1.5" u-bolts
two 2" u-bolts


CM220 Right-Angle Mounting Bracket

The CM220 Right-Angle Mounting Bracket can attach a sensor with a vertical pipe mount (e.g., most wind sensors) to a CM202, CM204, or CM206 crossarm. It is compatible with pipes that have a 1.0" to 1.5" outer diameter.
The CM220 is creased during manufacture to allow pipes of varying diameters to seat snugly into the bracket. The 90° bend in the middle of the bracket allows the CM220 to fill roughly the same role as the 1049 or 17953 NU-RAIL Offset Crossover fitting.

Features

Right angle mounting bracket
Vertically mounts a sensor to a crossarm

Specifications

Consists of a rectangular bracket and two 1.5" u-bolts


CM225 Solar-Sensor Mounting Stand

To make accurate measurements, solar sensors must be mounted where they are not shaded, and level. To achieve this, typically a leveling base and a mounting stand are required.
The CM225 mounting stand is used to attach one solar radiation sensor to a horizontal crossarm or vertical mast (1.0" to 2.1" OD). Compatible sensors include the LI200X, CMP3, LP02, and CS300 pyranometers, as well as the LI190SB Quantum Sensor. An LI2003S, 18356 Leveling Base, or similar base and leveling fixture may be required depending on the sensor selected.

Features

Solar sensor mounting stand
Leveling base or leveling fixture required
Can be mounted vertically or horizontally

Specifications

Consists of a rectangular plate, mounting bracket, u-bolts, lock washers, nuts


CM235 Magnetic Mounting Stand

The CM235 consists of rectangular plate, mounting bracket, u-bolts, lock washers, and nuts. It allows one peripheral with a magnetic base (typically antennas) to be mounted to a crossarm or mast (1.0" to 2.1" OD). Compatible peripherals include certain GPS or short-range omnidirectional antennas fitted with magnetic bases.


41003-5 10-Plate Radiation Shield

The 41003-5 is a naturally aspirated 10-plate radiation shield. Its louvered construction allows air to pass freely through the shield, keeping the probe at or near ambient temperature. The shield's white color reflects solar radiation.

Features

Provides a naturally aspirated radiation shield
Protects an HMP45C or HMP35C when exposed to sunlight
Mounts directly to our tripods and towers
Replaces the 41002 12-Plate Gill Radiation Shield
Manufactured by RM Young

Specifications

The 41003-5 attaches to a crossarm, mast, or user-supplied pipe with a 1.0" to 2.1" OD.


41303-5A Radiation Shield

The 41303-5A is a naturally aspirated 6-plate radiation shield. Its louvered construction allows air to pass freely through the shield thereby serving to keep the probe at or near ambient temperature. The shield's white color reflects solar radiation.

Features

Provides a naturally aspirated radiation shield
Used with HMP50, CS215, CS500, 107, or 108 probes
Mounts directly to our tripods and towers
Replaces our 41303 6-Plate Gill Radiation Shield
Manufactured by RM Young

Specifications

The 41303-5A attaches to a crossarm, mast, or user-supplied pipe with a 1.0" to 2.1" OD.

Producing Area:USA

related products

Inquiry online

Dianjiang Group Limited
Add: Room 1510,15/F,New Commerce Centre, No.19 On Sum Street, Shatin, N.T., Hong Kong.
Tel: (852) 3690 1588   Fax: (852) 3690 1586
Email: Dianjiang_HK@yahoo.com.hk   Hongkong@Dianjiangtech.com
© Dianjiang Group Limited All Rights Reserved.